PIC18F1230T-I/SO【PDF 59/318 页】IC PIC MCU FLASH 2KX16 18SOIC

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3871

55页 56页 57页 58页 [59页]60页 61页 62页 63页

PIC18F1230/1330

2009 Microchip Technology Inc.

DS39758D-page 151

15.1

Baud Rate Generator (BRG)

The BRG is a dedicated 8-bit or 16-bit generator that

supports both the Asynchronous and Synchronous

modes of the EUSART. By default, the BRG operates

in 8-bit mode; setting the BRG16 bit (BAUDCON<3>)

selects 16-bit mode.

The SPBRGH:SPBRG register pair controls the period

of a free-running timer. In Asynchronous mode, bits

BRGH (TXSTA<2>) and BRG16 (BAUDCON<3>) also

control the baud rate. In Synchronous mode, BRGH is

ignored. Table 15-1 shows the formula for computation

of the baud rate for different EUSART modes which

only apply in Master mode (internally generated clock).

Given the desired baud rate and FOSC, the nearest

integer value for the SPBRGH:SPBRG registers can be

calculated using the formulas in Table 15-1. From this,

the error in baud rate can be determined. An example

calculation is shown in Example 15-1. Typical baud

rates and error values for the various Asynchronous

modes are shown in Table 15-2. It may be advantageous

to use the high baud rate (BRGH = 1), or the 16-bit BRG

to reduce the baud rate error, or achieve a slow baud

rate for a fast oscillator frequency.

Writing a new value to the SPBRGH:SPBRG registers

causes the BRG timer to be reset (or cleared). This

ensures the BRG does not wait for a timer overflow

before outputting the new baud rate.

15.1.1

OPERATION IN POWER-MANAGED

MODES

The device clock is used to generate the desired baud

rate. When one of the power-managed modes is

entered, the new clock source may be operating at a

different frequency. This may require an adjustment to

the value in the SPBRG register pair.

15.1.2

SAMPLING

The data on the RX pin is sampled three times by a

majority detect circuit to determine if a high or a low

level is present at the RX pin when SYNC is clear or

when both BRG16 and BRGH are not set. The data on

the RX pin is sampled once when SYNC is set or when

BRGH16 and BRGH are both set.

TABLE 15-1:

BAUD RATE FORMULAS

Note:

A BRG value of ‘0’ is not supported.

Configuration Bits

BRG/EUSART Mode

Baud Rate Formula

SYNC

BRG16

BRGH

8-bit/Asynchronous

FOSC/[64 (n + 1)]

8-bit/Asynchronous

FOSC/[16 (n + 1)]

16-bit/Asynchronous

FOSC/[4 (n + 1)]

8-bit/Synchronous

16-bit/Synchronous

Legend: x

= Don’t care, n = value of SPBRGH:SPBRG register pair

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式